Carprog v8.21

Versiunea aceasta are toate optiunile active si are 540 de tokenuri (540 de utilizari reusite de programare sau scriere a unui device).NU ARE FUNCTII ONLINE!!!!!!!!

La aceasta versiune de Carprog toate optiunile sunt active.In comparatie cu celelalte variante aceasta are activa functia decode RNS510 (navigatie VW),functia de change km in bordurile echipate cu microprocesoare NEC (Laguna,Megane,etc) si ECU VAG.Programatorul este testat pe K-line si pe CAN (adaptorul A1),citire si scriere pe intreaga gama de memorii (24Cxx,93Cxx si 95xxx).se livreaza impreuna cu adaptorul de alimentare externa.

SE LIVREAZA PREGATIT PENTRU REFLASH AT90SAM7 IN CAZ CA APARE CONTOARUL CA URMARE A FOLOSIRII UNUI SOFT DIFERIT.ASIGUR REFLASUIREA -PRET 100LEI ( FAR TRANSPORT)!!!!

Carprog este un instrument proiectat special pentru a veni in ajutorul dumneavoastra atunci cand aveti nevoie sa aflati codul unui radio de masina, al unui bord sau al unui imobilizator dar nu numai atat. Cu carprog puteti face si programari de chei, modifica kilometrajul, clear-crash in calculatoare de airbag dar  si altele.

In versiunea de baza veti primi:

- adaptor cu 12 pini pentru EEPROM, avand in viitor posibilitatea sa faceti acelasi lucru ca un programator de tip microcontroler

- programator pentru imobilizatoare cu adaptor de antena pentru 125 de Mhz,

- diagnoza pe k-line ( programare a kilometrajului la bord, programare de chei noi),

- diagnoza pe CAN (+5V/+12V)

- alimentarea se face prin cablu usb sau exista posibiliatatea de alimentare externa.

CarProg Processor:

S2.1 - CARPROG Motorola (Freescale) HC05 MPU programmer

S2.2 - CARPROG Motorola (Freescale) HC11 MPU programmer

S2.3 - CARPROG Motorola (Freescale) HC08 MPU programmer

S2.4 - CARPROG Motorola (Freescale) 912 and 9S12 MPU programmer

CarProg Programmer:

ST92 - ST92F120, ST92F150, ST92F250 internal EEPROM programmer

CarProg Radio Code:

S6.1 - CARPROG CC1

S6.2 - CARPROG CC2

S6.3 - CARPROG CCN

S6.4 - Philips Car Radio decoder

S6.5 - Renault Car Radio decoder by serial number

S6.6 - Audi/VW/Seat/Skoda car radio decoding software

RNS510 - Navigation decoding tool by Navi diagnostic

 

Pachetul Cuprinde:

1: CarProg Main harware interface

2: A1 - OBD2 Adapter Cable

(Inside have K-line and CAN bus switches. Use with all cars complained with OBDII standard)

3: D1 - Odometer-airbag Adapter

(Dashboard ,Airbag programming adapter )

4: A3 - Transponder Antenna ( Used with all

CARPROG immobiliser software )

5: A10 - Motorola Adapter Cable 

(Motorola MCU programing adapter )

6: A11 - BMW EWS Adapter Cable

( Used with BMW Immo software )

7: A16 - Car radio Cable

( Used for Opel, Renault, Peugeot, Citroen car radio made by Philips decoding)

8: A15 - Cable

( Used with D1 adapter ,Universal car dashboard and airbag programming adapter )

9: A17 - Honda Airbag OBD2 Cable

( Adapter for Honda airbag reset by OBDII )

10: A4 - Eeprom Adapter Cable

( Used for eeprom programming)

11: A5 - DIP8 Clip Cable

( DIP8 Clip for eeprom programming)

12: A6 - SOIC8 Clip Cable

( SOIC8 Clip for eeprom programming)

13: A7 - MB 38-Pin Cable

(Used with MB Airbag and dashboard software)

14: A8 - BMW 20-Pin Cable

( Used with BMW airbag and dashboard software )

15: RNS510 Adapter Cable

( RNS510 radio decoding interface cable )

16: VOLVO FORD CAN 2006+ Cable

(Needed for airbag and dashboard programming)

17: FIAT CAN 2006 Cable

( Needed for airbag and dashboard programming)

18: C1 OBD2 Female Cable

19: USB Cable

20: Power cable

21: CD