Diagnoza Tesla PRO Scanner pentru modelele S, X si 3
2000
Lei
Nou, Cu factură, Cu garanție
Tesla PRO scanner Diagnostic and Programming Tool for TESLA S, X3,
Tesla PRO is the first independent device on the market supporting
diagnostics in TESLA model S, X and 3 so far.
You must be aware that the use of some for Tesla PRO functions in some
countries may be prohibited and against the law.
First of all, what you need to know about the Tesla PRO before work. Tesla PRO:
1.The tool is intended only for qualified personnel!
2.You must be aware of the risk of loss if something went wrong (learn keys or make adaptations of BMS controler or something else)
3.You must have electronic skills which allow you to make adapters yourself and the connection between Tesla PRO and the vehicle’s CAN interface.
4.Tesla PRO uses the CAN network to communicate with the ECU. Therefore, you will not have access to firmware, navigatie update, configuration because it cannot be done via CAN. All mentioned things do by LAN on IC,CID not via CAN network
TESLA PRO is a young software with small box interface but is constantly being developed.Can help you solve a few problems with the TESLA car. As so far, for TESLA PRO can work with ECU for TESLA Model S with some function for TESLA Model X and 3.
Tesla Pro Scanner is a programming tool specially designed for Tesla Model X/S after 2015 and Tesla Model 3 after 2019. It is the only independent device supporting Tesla Model 3/s/x diagnosis on the market so far.
Notion!!!! The client must be aware that using some TeslaPRO features may be prohibited and illegal in some countries.
First of all, what you need to know about the Tsla PRO before work. Tsla PRO: The tool is intended only for qualified personnel! You must be aware of the risk of loss if something went wrong(learn keys or make adaptations to the BMS controler or something else). You must have electronic skills which allow you to make adapters yourself and the connection between TeslaPRO and the vehicle's CAN interface.
Note: This tool can't suport the 2020 Tesla Model 3 Standard Range and 2018 Tesla Model 3 Standard Range.
Tesla Pro T-CAN PRO V2023.03 Diagnostic Tools Functions
T-CAN PRO can work with ECU TESLA Model S,X3,
T-CAN PRO Diagnostic Tools can only suport after 2015.09 Model S/Model X and after 2019 year Model 3
Before 2015, you can buy our cables to suport the cars.(If you have the need, pls contact us)
2020.11.16 – Beta Battery Energy data reading by can, factory mode (updated).
2020.11.05 – Global DTC decoding codes update.
2020.10.26 – some Lan functions added. (wakeup, punto drive, park DTC base)
2020.10.23 – CID commands Service and Factory Redeploy,
2020.10.22 – real-time by can level measure of TAS (EAS) Beta. (add some DTC base)
2020.09.25 – BMS contactor replacement procedure reset u019
2020.09.24 – m3 SDM read, erase DTC by can.
2020.09.21 last update. (Diag, Develop, FMODE by IC, Valet by LAN)
2019.05.23 NEW SDM by Bosch Module X and 3 models (read, clear fault codes and R/W EEPROM clear CRASH log.)
ALERTS – Alerts on CAN bus (read alerts codes updated BMS 2018.09.14 BETA STAGE !)
BDY – Body controler on CAN bus
DH – Door Handles – Learn Front Driver Side – CAN BDY -125 kbps (BETA Stage – added 15.07.2019)
SDM – Supplemental Deployment Module S model (read, clear fault codes, clear CRASH log by Boot mode pin.)
SDM by Bosch Module X and 3 models (read, clear fault codes, and R/W EEPROM clear CRASH log.)
SEC – Security controler (Add Keyfob Key)
PARK2 – Parktronic sensors (read and decode fault codes, erase stored fault codes) supported until 06.2016
THC – Thermal controler (Aer purge function)
EAS – Electronic Aer suspension System (read, decode, erase fault codes, exit service mode ) supported until 06.2016
TAS – Tesla Aer suspension System (erase fault codes, clear Crash event, exit service mode ) after 06.2016
BMS – Battery control Module (reset alert warnings w163,w026,w152,w153,w023,read softpack)
TPMS – Tyre Pressure (read senzor ID stored in memory it is useful if you need to make a new non-tesla senzor)
ESP – Electronic stability system (read and decode fault codes, erase stored fault codes)
What is T-CAN?
T-CAN PRO is a solution/diagnostic tool for Tesla cars that only consists of hardware and software.
Hardware
1. Car Programmer – plastic blue box with info label on top, inside is PCB (Printed Circuit Boards with semiconductors and SIM card). The device does not contain batteries
2. 2 Data cables (type: x437 and x437A) - these 2 cables are used to connect the car to the programmer
3. USB cable – this cable is using to connect the programmer to the PC or Laptop
NOTICE!!!
The tool is only for professional garages!
Tesla after the 2017 year
requires a different connector that this kit does not have
This Tool is designed for absolutely qualified personnel ONLY! For those who know the Tesla car and CAN network well.
Tesla T-CAN Pro
Packing List
1xT-CAN hardware
1xconnector/adapter x437
1xconnector/adapter x437A
1XUSB cable A/B
Compatibil cu:
Fiat Punto
Land Rover Range Rover
Nissan Note
Tesla Model 3, Model X, Model S
Piesă auto compatibilă cu:
Fiat Punto
Land-Rover Range Rover
Nissan Note
Land-Rover Range Rover
Nissan Note
Actualizat la:
06 Aug 2025, 09:11
06 Aug 2025, 09:11
Raportează
Actualizat la:
06 Aug 2025, 09:11
06 Aug 2025, 09:11
Raportează
Anunțuri similare